Washington state is known for its delicious apples. In fact, Washington produces 6 out of every 10 apples consumed in the United States! To highlight this local ingredient, applesauce from BelleWood Acres was added to this cold process recipe. BelleWood Acres is one of Northwest Washington’s largest apple orchards. It’s located just about 15 minutes away from the Bramble Berry offices and is a great addition to the community. Using a local ingredient in your soap is a fantastic way to highlight where it comes from and support other makers in your area.
Normally when one thinks apples, a deep color palette of red and green come to mind. But because this soap contains applesauce made with Honeycrisp apples, we used colors inspired by them. That means shades of bright red/pink, green and a touch of yellow. Then, a Hanger Swirl is used to pull the colors up and down to mimic the stripes on the apples. Apple Macintosh Candle & Soap Fragrance Oil gives the bars a slightly tart and fruity scent.
If you’ve never added a puree to your soap before, read this article to learn how. Don’t worry about the applesauce going bad in the soap. It goes through the saponification process along with the oils and lye. The high pH of the soap batter contributes to this process (which is why adding purees to melt and pour is not recommended). To account for the extra water in the applesauce, this recipe contains a 10% water discount. I also recommend soaping at slightly cooler temperatures to compensate for the sugar in the applesauce. If you live in a hot climate, you may want to place the soap in the fridge after pouring into the mold to keep temperatures cool. The extra natural sugar will contribute to a fluffy lather in the final bars of soap. When selecting the applesauce, make sure it does not have any extra ingredients like preservatives. These could cause unpredictable results in your soap.
What You’ll Need:
10″ Silicone Loaf Mold
Hanger Swirl Tool
9.5 oz. Olive Oil (27%)
10.5 oz. Coconut Oil (30%)
8.8 oz. Palm Oil (25%)
1.8 oz. Shea Butter (5%)
3.5 oz. Avocado Oil (10%)
1 oz. Castor Oil (3%)
5 oz. Sodium Hydroxide Lye
10.4 oz. Distilled Water (10% water discount)
2 oz. Applesauce
1.7 oz. Apple Macintosh Candle & Soap Fragrance Oil
Buttercup Mica
Kermit Green Mica
Sunset Orange Mica
Raspberry Mica
Click here to add everything you need for this project to your Bramble Berry shopping cart!
Find the supplies you need for this project below
If you’ve never made Cold Process soap before, stop here! I highly recommend checking out our FREE four part SoapQueen.tv series on Cold Process Soapmaking, especially the episode on lye safety. And if you’d rather do some reading, Bramble Berry carries a wide range of books on the topic, including my newest book, Pure Soapmaking. You can also checkout the digital downloads for that instant gratification factor.
SAFETY FIRST: Suit up for safe handling practices! That means goggles, gloves and long sleeves. Make sure kids, pets, and other distractions and tripping hazards are out of the house or don’t have access to your soaping space. Always soap in a well-ventilated area.
COLOR PREP: In separate containers, disperse 1 tsp. Buttercup Mica and 1 tsp. Sunset Orange Mica into 1 tablespoon lightweight liquid oil. Then in separate containers, disperse 1/2 tsp. Kermit Green Mica and 1/2 tsp. Raspberry Mica into 1/2 tablespoon lightweight liquid oil (like sweet almond or sunflower oil). Use a mini mixer to help get rid of any clumps.
FRAGRANCE PREP: Measure 1.7 ounces of Apple Macintosh Fragrance Oil into a glass, fragrance oil safe container. Set aside.
APPLE PREP: Measure out 2 ounces of applesauce. Set aside.
ONE: Slowly and carefully add the lye to the water and gently stir until the lye has fully dissolved and the liquid is clear. Set aside to cool. If you’d like a harder bar of soap that releases faster from the mold, you can add sodium lactate to the cooled lye water. Use 1 teaspoon of sodium lactate per pound of oils in the recipe. For this recipe, you’d add 2 teaspoons sodium lactate.
TWO: Fully melt and combine the coconut oil, palm oil, olive oil, castor oil, shea butter and avocado oil (remember to fully melt then mix your entire container of palm oil before portioning). Add the applesauce to the melted oils and stick blend for about a minute. Stick blending the applesauce before adding lye helps blend the applesauce into a smoother consistency without accelerating trace.
THREE: Add the lye water to the oils and stick blend until thin trace. After about 10-20 seconds of blending, you’ll notice the batter start to darken into a honey color. This is due to the sugar content in the applesauce.
FOUR: Once you’ve reached a thin trace, split the soap into four equal containers. Each container will have about 400 mL. Check out that color change!
FIVE: Add the following amounts of dispersed mica into each container. Use a whisk to fully mix in the color.
- Container A (pink): 1 tsp. dispersed Raspberry Mica + 1 tsp. Sunset Orange Mica
- Container B (green): 1 tsp. dispersed Kermit Green Mica
- Container C (orange): 1 tsp. dispersed Sunset Orange Mica
- Container D (yellow): All dispersed Buttercup Mica
SIX: Add the Apple Macintosh Candle & Soap Fragrance Oil evenly into each container (it’s okay to eyeball it). Use a whisk to fully mix in the fragrance oil into each container.
SEVEN: Begin pouring stripes of each color down the length of the mold. It doesn’t really matter what color you start with, or in what order you pour the colors. I started with orange, then poured in the pink, green and yellow. Pour the colors from various heights so they break through to the layer below. Don’t worry about being too precise with each pour.
EIGHT: Continue pouring the colors into the mold. Expect to have enough soap for about four pours of each color. Continue pouring until you have a small amount of each color for the top.
NINE: Insert the Hanger Swirl Tool into one side of the mold, all the way to the bottom. Drag the hanger against the bottom of the mold toward you. Once you drag the hanger about 1/8th of the way, pull the hanger up until it almost breaks through the top of the soap, but not quite. Move the hanger toward you about 1/8th of the way. Push the hanger back down into the soap, and drag the hanger against the bottom of the mold and move it toward you again, moving about 1/8th of the way. Bring the hanger up until it almost breaks the top, then move it over and push it back down. Repeat this process again, moving in the opposite direction. Only move the Hanger Swirl Tool vertically in the mold. This wasn’t my most precise hanger swirl, so don’t worry about making it perfect!
TEN: Tap the mold on the counter to help get rid of any bubbles. Drizzle each color on top down the length of the mold.
ELEVEN: Insert a chopstick or dowel into the very top of the soap (you only want to swirl the very top). Drag the tool down the length of the mold opposite of the direction you poured the soap on top to create the most interesting swirl. Don’t over swirl or the colors will muddle. Once you’re happy with the look, spritz the soap with 99% isopropyl alcohol to avoid soda ash.
Due to the extra sugar in the applesauce, this soap may have a tendency to get hot. If your room temperature is on the cooler side, you can leave it out on the counter without insulation for the first 24 hours. If you live in a hot climate, you may want to place the soap into the fridge for at least 2 hours up to overnight. Allow the soap to stay in the mold for about 3 days. Remove from the mold and cut into bars. Allow the bars to cure for 4-6 weeks and enjoy!
- 10″ Silicone Loaf Mold
- Hanger Swirl Tool
- 9.5 oz. Olive Oil (27%)
- 10.5 oz. Coconut Oil (30%)
- 8.8 oz. Palm Oil (25%)
- 1.8 oz. Shea Butter (5%)
- 3.5 oz. Avocado Oil (10%)
- 1 oz. Castor Oil (3%)
- 5 oz. Sodium Hydroxide Lye
- 10.4 oz. Distilled Water (10% water discount)
- 2 oz. Applesauce
- 1.7 oz. Apple Macintosh Candle & Soap Fragrance Oil
- Buttercup Mica
- Kermit Green Mica
- Sunset Orange Mica
- Raspberry Mica
- Slowly and carefully add the lye to the water and gently stir until the lye has fully dissolved and the liquid is clear. Set aside to cool. If you’d like a harder bar of soap that releases faster from the mold, you can add sodium lactate to the cooled lye water. Use 1 teaspoon of sodium lactate per pound of oils in the recipe. For this recipe, you’d add 2 teaspoons sodium lactate.
- Fully melt and combine the coconut oil, palm oil, olive oil, castor oil, shea butter and avocado oil (remember to fully melt then mix your entire container of palm oil before portioning). Add the applesauce to the melted oils and stick blend for about a minute. Stick blending the applesauce before adding lye helps blend the applesauce into a smoother consistency without accelerating trace.
- Add the lye water to the oils and stick blend until thin trace. After about 10-20 seconds of blending, you’ll notice the batter start to darken into a honey color. This is due to the sugar content in the applesauce.
- Once you’ve reached a thin trace, split the soap into four equal containers. Each container will have about 400 mL. Check out that color change!
- Add the following amounts of dispersed mica into each container. Use a whisk to fully mix in the color.
Container A (pink): 1 tsp. dispersed Raspberry Mica + 1 tsp. Sunset Orange Mica
Container B (green): 1 tsp. dispersed Kermit Green Mica
Container C (orange): 1 tsp. dispersed Sunset Orange Mica
Container D (yellow): All dispersed Buttercup Mica - Add the Apple Macintosh Candle & Soap Fragrance Oil evenly into each container (it’s okay to eyeball it). Use a whisk to fully mix in the fragrance oil into each container.
- Begin pouring stripes of each color down the length of the mold. It doesn't really matter what color you start with, or in what order you pour the colors. I started with orange, then poured in the pink, green and yellow. Pour the colors from various heights so they break through to the layer below. Don't worry about being too precise with each pour.
- Continue pouring the colors into the mold. Expect to have enough soap for about four pours of each color. Continue pouring until you have a small amount of each color for the top.
- Insert the Hanger Swirl Tool into one side of the mold, all the way to the bottom. Drag the hanger against the bottom of the mold toward you. Once you drag the hanger about ⅛th of the way, pull the hanger up until it almost breaks through the top of the soap, but not quite. Move the hanger toward you about ⅛th of the way. Push the hanger back down into the soap, and drag the hanger against the bottom of the mold and move it toward you again, moving about ⅛th of the way. Bring the hanger up until it almost breaks the top, then move it over and push it back down. Repeat this process again, moving in the opposite direction. Only move the Hanger Swirl Tool vertically in the mold. This wasn’t my most precise hanger swirl, so don’t worry about making it perfect!
- Tap the mold on the counter to help get rid of any bubbles. Drizzle each color on top, down the length of the mold.
- Insert a chopstick or dowel into the very top of the soap (you only want to swirl the very top). Drag the tool down the length of the mold, opposite of the direction you poured the soap on top to create the most interesting swirl. Don’t over swirl or the colors will muddle. Once you’re happy with the look, spritz the soap with 99% isopropyl alcohol to avoid soda ash.
- Due to the extra sugar in the applesauce, this soap may have a tendency to get hot. If your room temperature is on the cooler side, you can leave it out on the counter without insulation for the first 24 hours. If you live in a hot climate, you may want to place the soap into the fridge for at least 2 hours, up to overnight. Allow the soap to stay in the mold for about 3 days. Remove from the mold and cut into bars. Allow the bars to cure for 4-6 weeks and enjoy!
Hello,
I’m wondering about how many bars of soap you can get from this recipe. Please advise! Thanks!
Cut at 1 inch thick you should end up with 10 bars of soap.
This looks very fun to make! Do you have any recommended preservatives to increase the shelf life of soaps containing perishable ingredients?
Preservatives aren’t necessary because soap has a pH level that doesn’t allow mold to grow. Also, they’re designed to protect against mold and bacteria but they don’t extend the shelf life of fruit and vegetable purees.
The good news is once you add the perishable ingredients, they will turn into soap and have the same shelf life as your normal bars. Learn more in this post: https://www.soapqueen.com/bath-and-body-tutorials/tips-and-tricks/how-to-add-purees-to-cold-process-soap/
Do I have to use applesauce? I’d rather not have it as an ingredient. Can you help me alter the recipe?
You can leave the applesauce out if you like. It gives the soap a yellowish/orangey hue, so without it the colors will look different. You can prepare the same amounts listed above, but start out with less at first and see what you think. If you want to add more, you can go from there.
This recipe also has a water discount because of the liquid in the applesauce. You can use the full amount of water if you like. Find that amount with our Lye Calculator: https://www.brambleberry.com/Pages/Lye-Calculator.aspx
You can also keep the water discount if you like. It helps the soap unmold and cure more quickly, but it does accelerate trace as well. Learn more about water discounts here: http://www.soapqueen.com/bath-and-body-tutorials/tips-and-tricks/water-discounting-cold-process-soap-how-why/
If it’s a 10% water discount, wouldn’t I just add 10% more water? Or am I oversimplifying?
I made it, by the way, with applesauce. It is beautiful! I’d still rather skip the apple sauce next time, which is why I’m asking.
The full amount of water for this recipe is 11.6 oz. I found that by plugging the recipe into our Lye Calculator: https://www.brambleberry.com/Pages/Lye-Calculator.aspx
Hi, I am not sure if anyone else had this problem but the directions called for using ALL of the dispersed yellow Buttercup rather than the 1 -2 tsp of the others. This unfortunately turned so deep of a color that it looked very much like the orange and unfortunately I did not get a nice contrast with 4 colors. Why did the directions say to use all of this color because this would not have happened to me if I would have used the same proportions. Also I was wondering why essential oils are not used in the swirl recipes and this one. Is it because the essential oil promote a faster trace and does not allow for the extra time needed for the intricate work?
Thank you for any input you may have.
The Buttercup Mica is lighter in soap, so we added the full amount in our batch to get the color shown in the photos. Depending on the applesauce used and the temperatures, your soap may be darker so when the yellow is added it takes on more of an orange shade. Did you notice the soap was fairly dark?
You can use essential oils in this recipe if you like. Some oils like cinnamon leaf do accelerate trace, so make sure to read the descriptions before using it in this recipe.
Essential oils: https://www.brambleberry.com/Essential-Oils-C157.aspx
Find out how much to add with our Fragrance Calculator: https://www.brambleberry.com/Pages/Fragrance-Calculator.aspx
Since it has been several months, has this soap that you guys made turn brown yet?
Thanks.
Not yet, the colors are still nice and bright.
-Kelsey with Bramble Berry
Thank you Kelsey!
I was wonder if you think 10% SF would be too high. 30% CO dries my skin out to the point that I itch. If I lower the CO to 20% I get a much better bar that doesn’t dry my skin but has much less bubbles. Is there an oil I could include that helps with lather? I would love to make this recipe but I would definitely need to tweak it somehow l. Any input is greatly appreciated.
Absolutely, I think castor oil is a great option for you. If you drop the coconut oil to 20% and add 2-5% castor oil, it will give you really nice later. I would recommend keeping the superfat around 5%, as too high it can actually weigh down those bubbles.
Learn more about castor oil here: https://www.soapqueen.com/bath-and-body-tutorials/tips-and-tricks/sunday-night-spotlight-castor-oil/
You can also add sugar like apple, honey, etc. That boosts lather as well. Learn how to work with honey here: https://www.soapqueen.com/bath-and-body-tutorials/tips-and-tricks/use-honey-bath-beauty-products/
-Kelsey with Bramble Berry
Can I use fresh goat’s milk instead of distilled water for this recipe? It’s an absolutely fabulous recipe and I was wondering if I could make some tweaks to it
Absolutely! That will add a nice creamy feeling to the bars. 🙂
Learn more about working with milk here: http://www.soapqueen.com/bath-and-body-tutorials/tips-and-tricks/how-to-add-lye-to-milk-for-cold-process-soap/
-Kelsey with Bramble Berry
Can I use home made applesauce instead of purchased? Can other apples be used instead of honey crisp? This looks like such a fun soap to make! Thanks! 😃
Yes and yes! With the applesauce, we recommend using only apples and water. Additives like sugar can cause the soap to overheat. If you’re using fresh apples, you can puree them with a bit of distilled water (make sure to discount that from the main batch so it isn’t too wet). 🙂
Learn more about working with purees here: https://www.soapqueen.com/bath-and-body-tutorials/tips-and-tricks/how-to-add-purees-to-cold-process-soap/
-Kelsey with Bramble Berry
Hi,
I have some organic apple sauce that is about 5 months past its use by date as far as eating. Can i use it for this recipe. It has been kept in the pantry and is still sealed.
If the apples are past their shelf life, they may shorten the shelf life of the soap as well. They can cause it to go rancid more quickly. I would recommend making a batch with the apples now and using it up fairly quickly, or buying fresh apple sauce just to be safe. 🙂
-Kelsey with Bramble Berry
Thank you.
This is just very beautiful. Just joined this community and was motivated to making soap already. I have tried making a few soaps but no swirls yet.
Thanks so much Mayen! Once you’re ready to try swirls, this post has some helpful tips: https://www.soapqueen.com/bath-and-body-tutorials/tips-and-tricks/five-tips-swirling-cold-process-soap/
-Kelsey with Bramble Berry
These are just gorgeous! I love the color palette, it is just like a Honeycrisp apple.
Thanks so much Margaret!
-Kelsey with Bramble Berry
Ohhh sounds delicious! You have the best tutorial! Would the soap turn brown at the end of cure time due to the apple sauce? Thank you!
Thanks so much Sarah! The apples may brown eventually over time. That can happen with fresh ingredients like fruit. When we made soap with strawberries, it did brown. However, we made avocado soap and the bars never discolored. So far, the colors are staying true – no browning yet. 🙂
-Kelsey with Bramble Berry
Strawberries and Cream Cold Process Soap: http://www.soapqueen.com/bath-and-body-tutorials/cold-process-soap/strawberries-cream-soap-a-cold-process-tutorial/
Avocado + Spearmint Cold Process Soap: http://www.soapqueen.com/bath-and-body-tutorials/avocado-spearmint-cold-process-soap-tutorial/